Basic Operation

Turn the Phone On Adjust Ring Volume
Originate a Call Receive a Call
Use Incoming Call Vibration Notification

 

To Turn the Phone On2-5-1
Press the END/PWR key and hold for more than two seconds. The PSII displays the start-up greeting:

indicates communication is available.

If your Dterm PSII is out of the service area. The phone cannot be used until it is within your wireless coverage area. “No Service” indication may also indicate that the number of visitors limit has been exceeded when roaming.

NOTE: To turn phone off, press the END/PWR key and hold for more than two seconds.

To Originate a Call

2-5-22-5-3NOTE: To originate a call you must first make certain the battery is charged and phone is turned on.

  • Enter the telephone number.
  • Press the L1 or L2* key. PSII displays:NOTE: If Calling Party Name is not available then the calling party number will appear in the display for Mode 2* systems.

Or, for Offhook Dialing:

  • 2-5-22-5-3Press the L1 or L2* key. If Number Display is on, the PSII will momentarily display the extension number of the selected line.
  • Enter the telephone number. PSII displays:***Mode 2 features are only available on NEAX2000 IVS Series 1900 software or NEAX2400 IMX Series 7300 software & Dterm PSII Version 7.00/Zone Transceiver Version 5.00 software or later.

2-5-32-5-2To Receive a Call

    • As your Dterm PSII rings the Line LED will illuminate. PSII displays:NOTE: If Calling Party Number is not available, “CALL” is displayed. If Calling Party Name is not available then the calling party number will appear in the display (only for Mode 2* systems).
    • Press the L1 or L2* key (depending on what key is lit).
  • Begin speaking into the microphone.

To Adjust Ring Volume

NOTE: For Mode 2* systems, the ring volume controls both L1 and L2*.

2-6-5To Turn Off Ring:

    • Press the FNC/CLEAR button.
    • Press F2. PSII displays:
    • Press the F2 button again to turn off ring.
    • Press L1 to enter.
  • The silent ring icon will appear on the LCD display.

2-6-5To Turn Up Ring Volume:

  • Press the FNC/CLEAR button.
  • Press F3. PSII displays:
  • Press the F3 button to turn up volume.
  • Press L1 to enter new volume.

2-6-5To Turn Down Ring Volume:

  • Press the FNC/CLEAR button.
  • Press F1. PSII displays:
  • Press F1 button to turn down volume.
  • Press L1 to enter new volume.***Mode 2 features are only available on NEAX2000 IVS Series 1900 software or NEAX2400 IMX Series 7300 software & Dterm PSII Version 7.00/Zone Transceiver Version 5.00 software or later.

To Use Incoming Call Vibration Notification

NOTE: Incoming call vibration notification is not active when either L1 or L2* is busy.

2-6-3To Enable Incoming Call Vibration Notification:

    • Press the FNC/CLEAR button.
    • Enter 05 or 06 for Mode 2* systems. PSII displays:
    • Press F1 to turn on.
    • Press L1 to enter.
  • The incoming call vibration notification indicator (“V”) will appear on the LCD display.

2-6-3To Disable Incoming Call Vibration Notification:

  • Press the FNC/CLEAR button.
  • Enter 05 or 06 for Mode 2* systems. PSII displays:
  • Press F3 to turn off.
  • Press L1 to enter.*** Mode 2 features are only available on NEAX2000 IVS Series 1900 software or NEAX2400 IMX Series 7300 software & Dterm PSII Version 7.00/Zone Transceiver Version 5.00 software or later.