Your cart is currently empty!
PROGRAMMING
1.) From Windows, Click on START / SETTINGS / CONTROL PANEL.
2.) Double click on DATE / TIME.
3.) Enter a new time.
CONSIDERATIONS
Enter the time in 24-hour notation. In this scheme, that hours of the day are 0000 (12 midnight) to 2359 (11:59 p.m.). Since each time must have four digits, use leading zeroes when necessary. For example, to set the time to 9:00 a.m., enter ‘0900’. To set the time to 4:45 p.m., enter ‘1645’.
The time appears on system display phones as a.m. or p.m. (not in 24-hour format).
PROGRAMMING
To change the system time:
1. Press Feature 0 0 System Program System Program # 1 0 3.
2. Enter a new time in 24-hour notation. For example, to set the time to 2:15 p.m., press 1 4 1 5. The display reads:
System Time
Data 1 4 1 5
This time will appear on a system display phone as 2:15p.
3. Select another procedure or exit programming mode.
*Note, “System Program” = Left intercom button!
From station 120
To change system time:
1. Lift the receiver.
2. Press the Feature button FEAT.
3. Press the Speaker button [SPKR].
4. Dial 3.
5. Dial the current time : HHMM (24 hour clock format).
6. Hang up.
From station 120
To change system date:
1. Lift the receiver.
2. Press the Feature button [FEAT].
3. Press the Speaker button [SPKR].
4. Dial 2.
5. Dial the current date : MMDDYY.
6. Dial the day (78=Sun, 66=Mon, 88=Tue, 93=Wed, 84=Thu, 37=Fri, 72=Sat).
7. Hang up.
TO SET THE SYSTEM CLOCK, PERFORM THE FOLLOWING OPERATIONS WHEN THE MASTER KT IS IDLE.
OPERATION
1) Lift receiver, and listen for the dial tone.
2) Press the following buttons: FEAT + # + 2.
3) Enter the time in four digits, using the twenty-four hour clock. For example, to enter 1:35PM (13:35), press 1 + 3 + 3 + 5.
4) Hang up.
Time change must be performed at extension 20 only.
|
ACTION |
DISPLAY SHOWS |
| 1. Do not lift handset. | Current time ( e.g., 16 Wed. 3:52 p.m.) |
| 2. Dial 0. | Input Password |
| 3. Dial your three digit password (Default is 0 0 0 ). | Input No., Nxt,End |
| 4.Dial 0 0. | 00. time nn:nn |
| 5. Using the dial pad enter four digits for correct time; two digits for hour (00–23) and two digits for the minutes (00-59). | Numbers entered appear in sequence of entery on the display. |
| 6. Press Flash button twice. | Current time ( e.g., 16 Wed. 3:52 p.m.) |
Time change must be performed at the Attendant Console. (If customer does not have an Attendant Console at their site, we need to schedule a technician to change the time using one of our consoles.)
To Set the Time on the Console:
1. Press FUNCTION
2. Press ATT FUNCTION
3. Press SET TIME
The time (which can be in either the 12 or 24 hour format, depending on system programming), is entered as HH:MM, where the HH is hours and the MM is minutes. This example uses a 12 hour format:
When two digits have been entered for the hours, the “:” will automatically be displayed.
Options:
Press PM to register the time as after 12:00 PM, in 12 hour format
Press SET to enter the time as shown
Press EXIT
|
Action: |
Display Shows: |
| 1.) Press the ‘Feature’ button | Feature: |
| 2.) Dial ‘ * * 2 3 6 4 6’ | Feature: **23646 |
| 3.) If your display asks for a security code, then press ‘ * * 2 3 6 4 6’ again, otherwise skip | 1. System Speed Dial |
| 4.) Press the ‘Next’ button (as shown on the template) twice to get ‘3. Time and Date’ | 3. Time and Date |
| 5.) Once your display shows ‘3. Time and Date’, press the ‘Show’ button (found on template) | Time:<HH:MM> ; H = Hour, M = Minute |
| 6.) Press the ‘Change’ button | Hour: H H |
| 7.) Press ‘Change’ again to erase current hour | Hour:_ |
| 8.) Enter 2 digits for the correct hour on the dial pad using military time (the hour for 3pm is 15) Press the digit ‘1’ then the digit ‘5’ | Hour: 1 5 |
| 9.) Press ‘Next’ to get to the minutes | Minutes: M M |
| 10.) Press ‘Change’ to clear the current minutes. | Minutes:_ |
| 11.) Enter 2 digits for the correct minutes, e.g. for 3:46 press the digit ‘4’ then the digit‘6’ | Minutes: 4 6 |
| 12.) Press ‘Heading’ , found on template | Time:<15:46> |
| 13.) Press the ‘RLS’ button to end the session |
Time change must be performed at the attendant’s Multi-line Terminal.
example:
Friday,July4,1986,8:35a.m.
01. Depress CNF key and *
02. Hour Setting: Dial 0,8
03. Depress DSS key 20
04. Minute Setting: Dial 3,5
05. Depress DSS key 20
06. Day Setting: Dial 00,4
07. Depress DSS key 20
08. Month Setting: Depress line key 7
09. Depress DSS key 20
10. Year Setting: Dial 8,6
11. Depress ANS key to enter data
Steps can be performed from any phone
Do not Lift handset
01. Press Transfer
02. Press Conference
03. Press * (star)
04. Press Transfer
05. Press Conference
06. Press # (pound)
07. Press Redial
08. Enter 02
09. Press Recall
10. Enter 2
11. Press Recall
12. Enter HH, MM, SS
13. Press Conference
14. Lift and replace the hand set.
NEC Electra Professional Level I, Level II, Level II Advanced, Electra Pro 120, Electra Elite 48, Electra Elite 192
Steps must be performed from the main Reception phone (Usually Ext. 100 or 101)
TO SET THE TIME
1. Press FEATURE (FNC)
2. Dial 9#
3. Enter hour and minute using the dialpad
4. Press RECALL to change AM/PM setting
5. Press HOLD to change to calendar setting
OR Press FEATURE (FNC) to exit this feature
TO SET THE DATE
1. Press RECALL to select day of week
2. Dial # (pound) to move the cursor to day of month field
3. Enter day of month using the dialpad
4. Press RECALL to select month
5. Dial # (pound) to move the cursor to year field
6. Enter last two digits of year via dialpad
7. Press FEATURE (FNC)
Time change must be performed at Receptionist’s extension.
Action
1. Press The [ON/OFF] Button.
2. Press [PROG.] Button.
3. Dial [#] and Then [3].
4. Enter 4 Digits for the Year (e.g., 1995).
5. Enter 4 Digits For The Month And Day (e.g., 0406 for APRIL 6TH).
6. Enter Two Digits For The Hour (00-23).
7. Enter Two Digits For The Minutes (00-59).
8. Press The [ON/OFF] Button.
Description
Entry of current time.
Operation
1. Lift the handset or press the SP-PHONE button on extension 11.
2. Dial (77).
3. Enter the hour with 2 digits. (01 through 12)
4. Enter the minute with 2 digits. (00 through 59)
5. Dial (0) for AM or (1) for PM.
6. Press the # button.
7. Wait for the confirmation tone.
Conditions
- · Instantly after pressing the # button, new time counting will start.
- · Time setting is done through extension 11 only.
NOTE: The following procedure must be performed from extension 11
1.) Lift the handset or press the SP-PHONE button on extension 11
2.) Dial “77”
3.) Dial the hour (01 through 12)
4.) Dial the minute (00 through 59
5.) Dial 0 for A.M. or 1 for P.M
6.) Press #
7.) Hang-up
Timechange: Panasonic KXT1232 & KXTD1232
Time change must be performed at Receptionist’s extension.
|
ACTION |
YOUR DISPLAY WILL SHOW |
| Make sure your phone is on-hook and no calls are holding at your telephone. | |
| Press “PROGRAM” (or “PAUSE”) Enter” *” (“Star”) then” #” (“Pound”) and enter your System Password (default = 1234) | SYS-PGM NO? ARROW(left to right) |
| Enter “000” | Day/Time Set |
| Press “Next” | Display Example: ’98 Oct. 29 THU |
| Press “Next” again | Display Example: 12:00 AM |
| Enter the HOUR – to change the current entry, press “CLEAR” and enter the new hour | |
| Press “ARROW(left to right)” | |
| Enter the MINUTE – to change the current entry, press “CLEAR” and enter the new minutes | |
| Press “ARROW(left to right)” | |
| Press “SELECT” for AM or PM | |
| Press “STORE” | |
| Press “END” |
Occasionally, the system date and time need to be reset )for example, leap year or change to daylight-saving time). Any attendant can use the keyset to change the date and time that appear on all display keysets and in the SMDR and SMDA printouts.
NOTE: If you make a mistake, lift and replace the handset; then start over.
(1) While on hook, press SPCL and dial 021. [Displays SET TIME OF DAY.]
(2) Using the keypad, enter the time in hours and minutes. Then press * for AM or # for PM. For example, 900* = 9:00AM and 230# = 2:30PM.[Displays SET DATE MM-DD-YYYY.]
(3) Enter the month, day, and year. (For example, 01011986 = 01-01-1986.) If you make a mistake, backspace by pressing MUTE. [Displays SET DAY OF WEEK SUN.]
(4) Scroll through the day-of-week selection by pressing # to go forward or * to go backward. When the desired day is displayed, press SPKR to terminate programming. You hear a progress tone.
Timechange : Telrad 2464 Key GX
The attendant usually sets the time, although another station may be assigned this privilege. The time is set for all stations in the system even if there is a tenant service configuration.
To set the time from the key bx station:
1.) Press [spkr];
2.) press [#] (the display shows T AL) press [time]; enter the date and the time in the following order: – the month, using two digits (e.g. 09 for September); – the day of the month (e.g. 02 – the key bx will not accept 31 for September, November, etc.); – the time using four digits (e.g. 1430 for 2:30 p.m.);
3.) press [time] again;
4.) press [spkr] again.
If you hear an error tone, check that you have entered the correct number of digits for each element of the date and time.
Time change must be performed at Receptionist’s extension.
|
ACTION |
DISPLAY SHOWS
|
| 1.) Press the ‘spd dial’ button | “PROG” |
| 2.) Press the ‘time’ button | Alarm time is shown |
| 3.) Enter 4 digits for the present time (00 through 23 for hours and 00 through 59 for minutes) | Digits inputted will appear on display |
| 4.) Enter 2 digits for the date (01 through 31) | Digits inputted will appear on display |
| 5.) Enter 2 digits for the month (01 through 12) | Digits inputted will appear on display |
| 6.) Enter 2 digits for the year (00 through 99) | Digits inputted will appear on display |
| 7.) Press ‘save rpt’ or replace the handset |
Time change must be performed at Receptionist’s extension.
|
ACTION |
DISPLAY SHOWS |
| 1.) Press the ‘PROG’ button | “TIME” will appear of soft keys |
| 2.) Press the ‘TIME’ button | Alarm time is shown |
| 3.) Enter 4 digits for the present time (00 through 23 for hours and 00 through 59 for minutes) | Digits inputted will appear on display |
| 4.) Enter 2 digits for the date (01 through 31) | Digits inputted will appear on display |
| 5.) Enter 2 digits for the month (01 through 12) | Digits inputted will appear on display |
| 6.) Enter 2 digits for the year (00 through 99) | Digits inputted will appear on display |
| 7.) Press ‘SAVE’ & ‘SPKR’ |
Time change must be performed at Receptionist’s extension.
|
ACTION |
DISPLAY SHOWS |
| 1.) Press the ‘SPKR’ button then # | T AL |
| 2.) Press the ‘TIME’ button | |
| 3.) Enter the date & time in the following order:The month – using two digits (i.e. 09 for Sept.).The day of the month – also two digits.The time – using four digits
(i.e. 1430 for 2:30 PM) |
Digits inputted will appear on display |
| 4.) Press ‘TIME’ again | |
| 5.) Press ‘SPKR’ again |
Timechange : Tie Buscomplus / Ultracom AT
01.) At ext. 10, lift handset or press SPK key
02.) Press OPAC / CONF key
03.) Press CLOCK key
04.) Enter year (e.g., 1995)
05.) Press *
06.) Enter month and date (e.g., 0120 for January 20)
07.) Press *
08.) Enter number for day of week:
0 – Sunday
1 – Monday
2 – Tuesday
3 – Wednesday
4 – Thursday
5 – Friday
6 – Saturday
09.) Press *
10.) Enter time in terms of 24 hour clock (e.g., 1305 for 1:05 PM)
11.) Press *
12.) Hang up or press SPK key
Toshiba CTX
Enter program mode by pressing: Hold * # * # 1 * 2 * 3 *
Enter Password: 0000 Hold (Default password is 0000; that’s four zero’s)
At the “PROG=” prompt enter: 9 0 2 Hold
At the “SELECT PARAM” prompt press: Line Key 02
Enter time in 24 hour format: HHMMSS (Where HH is two digits for Hours, MM is two digits for Minutes and SS is two digits for Seconds)
To change program, press: Hold
To submit changes, press: Hold
And to exit program mode, Enter: # # Hold
Timechange : Toshiba DK8, DK16, DK24, DK56, DK96
Time change must be performed at Extension 10 or 200.
To Set the Date:
1.) Press Intercom
2.) Dial Intercom “651”
3.) Dial the Date (Dial year/month/day in the format “YYMMDD”. Enter a leading 0 for any single-digit month or day)
4.) Press the “Redial” button
5.) Press the “Spkr” button
To Set the Time:
1.) Press Intercom
2.) Dial Intercom “652”
3.) Dial the Time (Dial hour/minute/second in the 24-hours clock format “HHMMSS”. Enter a leading 0 for any single digit entered)
4.) Press the “Redial” button
5.) Press the “Spkr” button
To Set the Day:
1.) Press Intercom
2.) Dial intercom “653″
3.) Dial the Day (Dial “1″ =Sunday, “2” =Monday, “3” = Tuesday, “4” = Wednesday, “5” = Thursday, “6” = Friday, “7” = Saturday)
4.) Press “Redial“ button
5.) Press the “SPKR“ button. You will hear a Confirmation tone
Timechange : Toshiba DK14, DK16e, DK40, DK280, DK424
Time change must be performed at extension 200:
1. Do Not Lift the handset
2. Press the “ICM“ button
3. Dial “#652“
4. Enter the Time in military format(i.e. “13:30:00” for 1:30 pm, display will confirm your correct entry)
5. Press “Redial“ button
6. Press Speaker button
Timechange : Toshiba Perception
Time change must be performed at the Attendant Console. (If customer does not have an Attendant Console at their site, we need to schedule a technician to change the time using one of our consoles.)
To Display Time:
Press the DIS TOD key a second time
The time is then displayed:
SRC COS DEST
Hours Minutes Seconds
To Set Time:
Enter the 6-digit time (via the dial pad) in the following format:
HHMMSS (Example: For 9:30 AM enter 093000 / For 9:30 PM enter 213000)
To Start the Clock and Clear the Display:
Press the DIS TOD key a third time to clear the display
Note: The display automatically clears if an LPK key is pressed
Timechange : Toshiba Strata 6E, 12E, 20E
This operation is possible from station 10 only.
TO SET DATE
1) Handset on-hook.
2) Dial “# * 5 1“ (or “RDL REP 5 1“).
3) Dial in date (year / month / day) in the format “YYMMDD”.
Enter a leading 0 for single digit month and day.
4) Depress the “#“ (or “RDL“) button.
TO SET TIME
1) Handset on-hook.
2) Dial “# * 5 2” (or “RDL REP 5 2”).
3) Dial in time (hour / minute / second) in 24-hour clock format
“HHMMSS”. Enter a leading 0 for single digit.
4) Depress the “#” (or “RDL”) button.
TO SET DAY
1) Handset on-hook.
2) Dial “# * 5 3“ (or “RDL REP 5 3“).
3) Dial in the day (“1“ represents SUN, “2“ MON, etc. through “7“ for SAT).
4) Depress “#“ (or “RDL“) button.
Timechange : Trillium Panther II
(Master Attendant Only)
Setting System Date
1.) Press the “PROGRAM” key and dial “06“
2.) Enter a 2-digit YEAR (00-99) (e.g., enter “88“ for 1988)
3.) Enter a 2-digit MONTH (01-12) (e.g., enter “02“ for Feb., 1988)
4.) Enter a 2-digit DAY (01-31) (e.g., enter “06“ for Feb. 6th, 1988)
5.) Enter a DAY OF THE WEEK code:
“1“ = Sunday
“2“ = Monday
“3“ = Tuesday
“4“ = Wednesday
“5“ = Thursday
“6“ = Friday
“7” = Saturday
6. Press “*“ to exit programming mode
Setting System Time
1. Press the PROGRAM key and dial “07“
2. Enter a 2-digit HOUR (00-23) (e.g., enter “15“ for 3 p.m.)
3. Enter a 2-digit MINUTE (00-59) (e.g., enter ‘10 “ for 3:10 p.m.)
4. Press “*“ to exit programming mode